For the sake of this example, we’ll be looking at a catalyzed polyurethane finish on a pedal steel guitar. Start with 600 grit paper. Resist the urge to wrap the paper around your fingers and start sanding. Using your finger will create uneven pressure and cause your finish to look wavy.
Also question is, can I sand my guitar neck?
To get started, cup your hand around the neck with the sandpaper so you have contact with the entire surface area. The first few strokes will cut into the finish and you can see if you need to apply or release pressure in any spots. Also, make sure you run the sandpaper the full length of the neck.
Accordingly, can you go from 60 grit to 120 grit? Summary: A good general rule for grit progression is to use 100 or 120 grit for initial sanding, 150 or 180 grit for the next pass, and 220 grit for the final pass.
| Grit | Coarseness Level |
|---|---|
| 40-60 | Coarse |
| 80-120 | Medium |
| 150-180 | Fine |
| 220-240 | Very Fine |
Furthermore, can you sandpaper a guitar?
You can use a fine grain of sandpaper of to smooth out the wood on the guitar. You’re going to want to work over the entire body of the guitar with a medium grit sandpaper (120 grit) and go back over again with the entire body and use an even finer grit of paper (220 grit).
How do you finish a polyurethane guitar?
How do you finish frets?
Fret Dress and Fret Leveling Tools You Will Need
- 2.1 Cover Magnetic Pickups.
- 2.2 Check for Loose Fret Ends.
- 2.3 Adjust the Truss to Straighten the Neck.
- 2.4 Clamp the Body and Neck Down.
- 2.5 Mask/tape off the Fretboard.
- 2.6 Mark the tops of the Frets.
- 2.7 Level the Frets with a Leveling Bar.
- 2.8 Re-mark the tops of the Frets.
How do you get clear coat off a guitar?
Just sand it with 2000 grit sandpaper until all the shiny spots are gone. you dont need to take it off to get a satin finish. Just sand it with 2000 grit sandpaper until all the shiny spots are gone. the little sparkles are in the paint not the laquer.
How do you get rid of sharp fret edges?
Filing fret ends.
The first step is to file the protruding fret ends flush to the fretboard. Hold the fine-tooth flat file against the side of the fretboard and gently drag the file from the first fret down to the last fret (Photo 4). Let the tool do the work—you’re just guiding it.
How do you sand a guitar finish?
How do you smooth rough frets?
How do you wet sand a guitar body?
What grit sandpaper for guitar fret ends?
Standard sandpaper would typically be around 120 grit, whereas these papers go up to around 12000 grit! You should start with 1500 grit , then, as a good guide, work your way through 2400, 3600, 8000 and finally 12000. The 1500 will even up the frets and give them a nice shine.
What is 7000 grit sandpaper used for?
Perfect for sanding metals and automotive finishes. Made with Silicon Carbide grain which retains its sharpness throughout its sanding life. Excellent flexibility of soaked material.
What is 800 grit sandpaper used for?
800-1000 grit sandpaper is ultra fine. It’s used for final sanding and polishing of thick finishes.
Which grit of sandpaper will give you the smoothest finish?
For heavy sanding and stripping, you need coarse sandpaper measuring 40- to 60-grit; for smoothing surfaces and removing small imperfections, choose 80- to 120-grit sandpaper. For finishing surfaces smoothly, use a super fine sandpaper with 360- to 600-grit.