They’re for an effects loop. the send and return is for the effects loop, if you jack a cord out of the send jack and through some pedals and then back to the return those pedals will work beneath the amps ordinare controls, you can also use the send jack to plug in a recording device as you said.
People also ask, do I use input or output on amp?
A signal is traveling out of the amp and into the headphones. The “aux in” jack on your amp, however, is just that–an input. The signal from your mp3 player, CD player or other outboard devices is traveling into the amp. Similarly, the “line out” jack on the back of your amp is just that–an output.
Additionally, do RCA cables go to input or output on amp? Your amplifier gets its input signals from the receiver’s output typically via RCA cables. RCA cables come in stereo pairs, in various lengths. When running new speaker wires from your amplifier’s output to the speakers, any size wire from 18- to 14-gauge will work fine.
Besides, how do I use Send effect?
How does send and return work?
What are sends and returns? Sends and Returns let you run multiple sounds through the same effect in your mix. No more putting a reverb on every different channel and trying to duplicate the settings knob-by-knob. Each Return channel in your DAW allows you to set up an effect on a separate channel.
Is FX send mono or stereo?
The bus appears at the console’s FX send output and can be fed from there to an external effects device. The return from the effects unit is then brought back into the console on the stereo channels. Each FX send is mono and features up to +15 dB gain.
Is FX send the same as aux send?
Aux sends are sometimes labeled with different names such as “effects send,” “FX send,” MON (short for “monitor”) or even “foldback,” but they all work the same way: They serve as a secondary output from a channel that routes the signal to a place other than the main left and right speakers.
Is send output return input?
You would use the “send” jack to the input on the effects unit and output of the effects unit to the “return” jack. This usually prevents any unwanted noise from placing the effects before the input section on the amp. Hope this helps! Billy, those are the preamp send (output) and preamp return (input) for the amp.
Should chorus go in effects loop?
A chorus pedal is traditionally used in the effects loop of a guitar amplifier. There’s no right or wrong necessarily, as they can sound great in the front end of your amp too.
Should distortion be in effects loop?
To summarize, we would not recommend putting a distortion pedal in your effects loop. Instead, put it in the main line between your amp’s input and your electric guitar. It’ll help the distortion pedal interact better with your preamp and will sound more natural when moving from a clean to a distorted sound.
What is a combo amp?
A combo amp has the amplifier and speaker, just like a head and cabinet setup, but everything is in one piece of equipment instead of two. These are some of the perks of a combo amp: Compact: Even though the head and cabinet may be lighter to carry, it’s more inconvenient.
What is FX loop on guitar amp?
An FX Loop is essential an insert point in your amplifier circuit that allows you to insert a piece of gear after the preamp circuit, but before the power amp circuit. Some guitar players are happy to run everything into the front end of the amp, and others prefer to insert certain effects types into the loop.
What is the 4 cable method?
The 4 cable method is a way to hook up a pedalboard to an amp in a way that allows you to control which pedals or effects are placed before the pre-amp and which pedals or effects are placed after the pre-amp in the amp’s effects loop. This is achieved using four cables hence the name.
Where does Looper go in pedal chain?
Normally, you’ll want the looper to be able to record and playback any of your sounds. Of course, this means you should place it at the very end of the chain so it can hear and record whatever pedal combinations you use.
Why do guitar amps have 2 inputs?
An amp has multiple inputs to allow you to connect audio sources correctly. High impedance instrument connects to the high input whereas a low impedance instrument connects to the low input.